Skip to main content

The Part Changed After Approval. Does Your O&M Manual Know?

A swap after the stamp leaves the submittal and O&M manual describing gear that isn't on the wall. Log it once, resubmit it, check every sheet.

When a part changes after the submittal was approved, treat it as a revision, not a note. Get the swap in front of the engineer under the same submittal number, change the part in the one list your submittal and O&M manual both print from, and before closeout check every datasheet in the manual against the catalog number on the nameplate.

The flow meters were approved in March. In June the distributor calls: the approved model is now 22 weeks out, but the sister model with the same liner and electrode material is on the shelf. Your PM says yes, the meters show up in July, and they work fine.

The change lives in an email, a note on the PO, and a sticky note on the panel drawing. The submittal still says the old model. So does the O&M manual, because it was built from the approved submittal. At closeout the owner's reviewer walks the plant with your binder, finds three meters whose nameplates match nothing in it, and bounces the whole manual. Now you're reconstructing a decision from June out of your inbox.

Why parts change after the stamp

An approval stamp says "this is what you intend to supply." Then the job happens:

  • Lead times. The approved item slips past the date you need it, and something equivalent is available now.
  • Obsolescence. The manufacturer announces end of life between approval and the order, and ships the replacement instead.
  • Change orders. The owner adds a fourth pump, a different signal type, or a bigger panel, and the device that fit the old scope doesn't fit the new one.
  • The order itself. Purchasing buys a different option code than the one you submitted, because it was the one the distributor's quote said.

None of these are unusual. What makes them expensive is that each one updates one document and leaves the rest describing the old part.

A sticky note is not a record

The engineer approved a specific product. Anything else on the wall is unapproved until they see it, however equivalent it is. Some specs treat a post-award change as a substitution with its own procedure, and substitution requests and the or-equal clause covers finding it. Either way, the engineer has to hear about it from you, in writing, before closeout.

So send it as the next revision of the submittal that covered the part. Same number, next rev, and only the item that changed. The reviewer already approved everything else, and revising without rebuilding the whole package keeps it that way. Rev 0 stays on the record as what was approved in March. Rev 1 says what changed in June and why.

The email, the PO note and the sticky note all count as reminders. None of them counts as a record, and none of them will be in the binder.

Change the part once, where everything prints from

The swap touches more than the product data sheet. The panel bill of materials lists the old catalog number. The O&M manual carries the old datasheet and the old installation and operation manual. The spare parts list may name the old spare. The warranty section may carry the old manufacturer's warranty.

If each of those is its own spreadsheet or folder, the swap has to be typed into each one by hand, and the one you miss is the one the owner finds. Keep one equipment list per project, and have the submittal and the O&M manual both read from it. Then the swap is one edit: the old part out, the new part in, with its own datasheet and manual. Every package that holds the item picks it up.

Whatever you use, the test is the same. After the edit, can you open the O&M manual and find the new model's datasheet and manual and nothing of the old one?

Check every datasheet against the nameplate

Swaps you were told about are the easy ones. The hard ones are the ones nobody mentioned: the option code purchasing changed, the panel shop's substitution for an out-of-stock relay, the instrument the field replaced after it was damaged in shipping.

Before the O&M manual goes out, check what's installed against what's in the manual:

  1. Get the installed catalog numbers. From the nameplates, the panel shop's final BOM, or the receiving records. Not from the submittal.
  2. Put them beside the manual. One row per tag: tag, catalog number on the nameplate, catalog number on the datasheet in the manual.
  3. Chase every mismatch. Each one is either a swap the engineer hasn't seen, which needs a revision, or a datasheet that's simply wrong, which needs replacing.

This is the same check the reviewer is about to run with your binder, so run it first. The rest of what the binder needs is in how to build a control panel O&M manual.

Say it on the transmittal

The person who reviews Rev 1 may not be the person who approved Rev 0, and they won't hunt for what changed. Tell them in the transmittal's notes, one line per item:

FIT-101 to FIT-103: provided with the manufacturer's sister model in place of the model approved in Rev 0, due to a 22-week lead time on the approved model. Liner, electrode material, size and output match the approved submittal. Revised datasheet attached and highlighted.

Name the tags, the reason, and what stayed the same. A reviewer who can check your claim on one highlighted page approves it in one sitting. What a transmittal has to say covers the rest of the cover sheet.

When the O&M manual goes out later, the same line on its transmittal saves the owner's reviewer from wondering why the manual and the approved submittal disagree.

How Submittal Kit handles this

The swap shouldn't mean retyping the same part into three documents. In Submittal Kit every project keeps one Equipment Register, and every submittal reads from it. Open the item, and in its Part panel choose Relink to a different part. The item keeps its tag, quantity and place in the tree, and its selected documents switch to the new part's datasheet and manual. If the tags carried their own order codes, enter them again, since a part change clears them. Every compiled package that holds the item tells you equipment changed since it was compiled, so a stale PDF can't go out by accident.

An O&M manual created from the submittal shares its equipment list live, so the manual has the new part as soon as the submittal does, with nothing retyped. The issued submissions stay frozen: Rev 0 still shows exactly what was approved. Mark Rev 1 as submitted issues the swap under the same number, and its Since line on the log lists the new model's documents as added and the old model's as removed. Type the reason into the transmittal's Notes, which print in the compiled package.

Before either package goes out, the Checks tab flags any selected datasheet that never prints the item's catalog number, which is how a mismatched sheet usually shows up, and its Lifecycle row warns when a part is listed as obsolete before the swap is forced on you. Changing the part also marks the Spec Check out of date, so you know to run it against the new model. Reading the nameplates in the field is still yours. See Checks before you submit and Issue a submission.

Disclosure: I build Submittal Kit. The revision, the nameplate check and the transmittal line work with a spreadsheet and a PDF editor too.

Where this lives in Submittal Kit

Want to see your BOM become a reviewable package?

Bring a CSV or Excel BOM, or use a demo project. You'll see the proposed matches before anything changes and review the compiled PDF before issue.

Book a walkthrough